WHY YOU SHOULD THINK ABOUT HIRING A PLUMBER FOR DISHWASHER INSTALLATION

Why You Should Think about Hiring a Plumber for Dishwasher Installation

Why You Should Think about Hiring a Plumber for Dishwasher Installation

Blog Article

Click Here

From hauling a dishwasher into your house to connecting the water connections, mounting a dishwashing machine can use up to five hrs. If you do not have the right tools, it might take even longer. To make your life less complicated and to prevent mounting a dishwashing machine incorrectly, we recommend employing a professional plumber. A plumber will have the right devices handy and also can install your brand-new dish washer in under two hrs. If you're not quite convinced yet, keep checking out to learn why you must employ a plumber.

A Plumber Can Check the Supply Lines


A supply line, especially a dish washer connector, attaches the dishwasher to a water source. A plumber can make sure that the line is suitable with both your dishwasher and also water source if you get a new supply line. If you decide to make use of an existing supply line, a specialist plumber can inspect it to make sure that it remains in good condition as well as does not have any type of leaks.

An Improper Installation Can Nullify the Dishwasher's Guarantee


Before installing a dishwasher on your own, you need to review the warranty carefully. Unless you are convenient as well as have experience mounting dishwashers, you must employ a plumber so you don't risk your warranty.

Setting Up a Dishwashing Machine Needs a Selection of Devices


If you do not have a variety of tools on hand, you may require to make a journey to Lowe's or House Depot. To install a dishwashing machine, you need the complying with devices: pliers, a flexible wrench, a collection of screwdrivers, a tube cutter, as well as hole saws.

Not Mounting Your Dishwasher Correctly Can Cause a Mountain of Troubles


Not only can mounting a dishwashing machine properly invalidate your service warranty, yet it can also create a mess. If you improperly install your dish washer to the waste disposal, you might observe pungent smells or have deposit on your dishes.

A Plumber Can Complete the Work Affordably and Quickly


A plumber can install your dishwasher in one to two hrs. The typical plumber will not bill more than a pair of hundred bucks to mount your dishwashing machine.
From carrying a dish washer into your home to connecting the water links, setting up a dishwasher can take up to 5 hrs. To make your life much easier and also to avoid mounting a dish washer improperly, we suggest hiring a professional plumber. A plumber will certainly have the right tools on hand as well as can install your brand-new dishwashing machine in under 2 hrs. A supply line, especially a dishwasher adapter, links the dishwashing machine to a water source. Unless you are useful and also have experience mounting dishwashing machines, you need to hire a plumber so you do not risk your service warranty.

How To Install A Dishwasher


Installing A Dishwasher Yourself


Just like other home appliances, a dishwasher helps to make chores less time-consuming and free of hassle. Most modern kitchens have a dishwasher or a cabinet space for dishwasher installation built into them. An older kitchen with no dishwasher or cabinet space for one might require a little reconstruction to accommodate dishwasher installation.


Installing a dishwasher requires basic knowledge of plumbing and electrical wiring. This article contains the steps involved in dishwasher installation, dishwasher installation tips, things to consider when installing a dishwasher in a kitchen that previously had no dishwasher in it, and tips for maintaining a dishwasher.


Steps Involved In Dishwasher Installation


Step One: Gather the Necessary Supplies


Gather all the required items and keep them near the installation site for easy reach. The materials and tools you will require include the following:


  • A screwdriver

  • • A hose clamp

  • • Duct tape (optional)

  • • A brass fitting

  • • Teflon tape

  • • A pair of pliers

  • • An adjustable wrench

  • • A drill

  • • Braided steel water line

  • • A pair of rubber hand gloves (optional)

  • • Wire nuts

  • Step Two: Take Safety Measures


    First, turn off the power socket and unplug the power cord if it is a plug-in dishwasher. Then, proceed to turn off the circuit breaker. Next, turn off the hot water shut-off valve under the kitchen sink and run the tap to ensure the water supply is shut off. Protect your kitchen floor close to the installation area with an old rug or a piece of drop cloth.


    Step Three: Remove the Old Dishwasher


    This step only applies if your kitchen has an old dishwasher that you want to replace. Remove the cabinet door to gain complete access to the old dishwasher. Next, remove the cover of the access panel located at the bottom front side of the dishwasher. Locate the junction box inside the access panel.


    Now, unscrew the terminal screws holding the wires in place at the junction box. Then, remove and tuck the wires out of the way with duct tape. Locate the dishwasher water inlet tube, undo the brass fitting and disconnect the water supply pipe from it. Put the disconnected end of the water supply line pipe into a bucket or bowl to collect any water remaining in it.


    Reach down beneath the sink to undo the drain hose. Loosen, then clamp and disconnect the drain hose of the dishwasher from the tailpiece of the sink. Next, put the disconnected end of the drain hose into a bucket to collect the water and debris.


    With all the connections out of place, remove the screws holding the dishwasher in place with a screwdriver, gently pull the dishwasher out from the cabinet and set it aside. You can use a piece of cloth or towel to clean up the mess made or any water spillage on the floor. Also, clean the cabinet where the old dishwasher was before installing a new one.


    Skip this step if you are having a dishwasher installed for the first time in your kitchen.


    Step Four: Install the New Dishwasher


    Connect the Water Supply


    Wrap Teflon tape on the tip of the water inlet pipe located at the bottom of the dishwasher. Screw on the 90 degrees brass fitting to the taped inlet pipe and tighten it with an adjustable wrench. Most dishwasher units do not include a brass fitting, but they are available at hardware stores.


    Once you have the fitting, connect the new water supply line to the elbow of the brass fitting. Pass the other end of the waterline through one of the cabinet holes and place it on the floor beneath the kitchen sink.


    Attach the Drain Line


    Locate the dishwasher drain standout pipe, connect the drain line to the dishwasher, and secure the connection with a hose clamp. Pass the other end of the drain line through the cabinet hole and place it towards the sink drain tailpiece


    Slide the Dishwasher into Place


    Attach the adjustable legs to the front of the dishwasher. Carefully slide the dishwasher under the countertop into the cabinet. Stop halfway and ensure everything is in a good position before sliding it in completely. Finish hooking up the water line by connecting the other end to the dual shut-off valve located under the kitchen sink.


    Proceed to connect the drain hose through an air gap to your garbage disposer, if you have any, or to the drain tailpiece of your sink. If you do not have an air gap, make a high loop with the drain hose before connecting it to the garbage disposal or the sink drain tailpiece.

    https://www.movementplumbing.com/blog/how-to-install-a-dishwasher


    How to install a dishwasher safely
    Visit Site

    Report this page